New Pro Quality

ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW

ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW

ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW    ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW
ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW. Maximum speed: 18,000 rev / min. Speed mode: through the inverter to adjust the output voltage and frequency can be achieved 0-18000 stepless. The working environment temperature of the GDF series air-cooled electric spindle is usually -10. Before starting the installation, first turn the shaft of the air-cooled electric spindle by hand. It should be flexible and free from blockage. Check the stator insulation resistance of the stator with a 500V shaker of not less than 50M. Select the inverter to match the voltage, power and frequency of the air-cooled electric spindle. Special Note: When installing the fixing screws on the square air-cooled electric spindle, you must apply thread glue to prevent loosening! Connect the inverter to the three-phase power supply of the air-cooled electric main shaft, and then connect the inverter to the external power supply to observe whether the rotation direction of the air-cooled electric main shaft is consistent with the direction indicated by the air-cooled electric main shaft. If it is inconsistent, it should be shut down immediately and air-cooled.

The motor spindle is strictly prohibited from operating in the wrong direction of rotation. The connection between the air-cooled electric spindle and the inverter should not exceed 25m. When installing the tool, the air-cooled electric spindle should remove the dirt on the surface of the shaft head taper and the spring chuck to avoid reducing the precision. Special tools should be used when clamping and removing tools.

Be careful not to use excessive force during clamping and disassembly. Due to the limitation of the limit speed of grease lubrication of precision angular contact ball bearings, the air-cooled electric spindle is not allowed to run at over speed. Overspeed operation can cause the precision angular contact ball bearing to burn out.

When using the air-cooled electric spindle, the vacuum cleaner should be used in combination to clean the dust generated during the process to avoid the heat generated by the air-cooled electric spindle. In severe cases, the air-cooled electric spindle will burn out. When the air-cooled electric main shaft is working normally, if there is any abnormal sound appearing on the air-cooled electric main shaft, the abnormal sound should be shut down and checked in time. Second, the wind-cooled electric spindle is heated and the vibration is stable. If the heat and vibration are intensified, the shutdown is checked in time.

Third, see if the surface quality of the processed surface is stable, such as unstable and timely shutdown inspection. The problem often occurs in the operation of the electric spindle. The air-cooled electric spindle often encounters heat during normal operation. Always check whether the air-cooled electric spindle's outer casing and air duct are clogged with dust. If the dust is clogged, it should be cleaned up in time. If it is not cleaned up in time, the air-cooled electric spindle will be heated, causing the air-cooled electric spindle to burn out in severe cases. When the air-cooled electric spindle is running and the sound or vibration is abnormal, stop the bearing immediately and replace the new bearing if necessary.

When an abnormal smell or sudden stop occurs during operation, the power should be cut off immediately. The stator-to-ground resistance and three-phase resistance should be measured with a shaker. If the insulation resistance is lost, the stator should be burned out.

When the air-cooled electric spindle is out of service for a long time, the shaft head and the taper hole of the air-cooled electric spindle should be rust-proofed. After the air-cooled electric spindle is stored or deactivated for 6 months, it must be replaced with new grease before it can be used, otherwise it will affect the life of the air-cooled electric spindle. In order to extend the service life of the air-cooled electric main shaft, the new air-cooled electric main shaft or the air-cooled electric main shaft with new bearings should be divided into 4 to 8 speeds within the speed range, and each speed should be increased after 30 minutes, avoiding direct High speed operation shortens the service life of bearings.

After the holiday, the air-cooled electric spindle is turned on for half an hour after the start-up, and then the work starts. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday.

This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Electric Motors\General Purpose Motors". The seller is "autocomponents999" and is located in this country: US. This item can be shipped to United States.

  • * Feature *: Creative Design,Durable Material,Beautiful Appearance
  • Feature 1: Easy installation,Convenient Use,Easy Operation
  • Note:: Do not send to Brazil
  • Bundle Description:: No
  • shipping notice: Can not ship to Puerto Rico,Alaska/Hawaii
  • Item location:: CA /NJ /Austell
  • Transportation does not include:: canarias
  • shipping notice:: Can not ship to Puerto Rico,Alaska/Hawaii
  • Brand: Unbranded/Generic
  • Output Power: 2.2KW
  • Voltage: 220V
  • Shaft connection: ER20
  • Maximum speed: 18,000 rev / min
  • Cooling: air cooling mode
  • Material: 304 stainless steel
  • Diameter: 80mm
  • Current: 6 A
  • Current Type: AC


ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW    ER20 Professional Air-cooled Spindle Motor High Quality 220V 18000rpm 2.2KW